Causes and Solutions of Transparent Defects in Plastic Moulds

Causes and Solutions of Transparent Defects in Plastic Moulds

Causes and Solutions of Transparent Defects in Plastic Moulds
Plastic mold is the mother of industry, and now the release of new products will involve plastic. Plastic mold molding technology is a widely used production method of plastic products. Many kinds of plastic products are produced by plastic manufacturers using plastic machines. For example, the mobile phone case that is very popular in our life is one of them. However, many plastic mold manufacturers with immature technology often show some shiny silver lines when making transparent products using TPU, PC and other materials, As a result, the aesthetics of products are greatly affected. What are the reasons for the quality problems of such transparent plastic parts? How to solve it?
In fact, the quality defects such as craze, craze, crack polystyrene, plexiglass and other transparent products, such as craze, flicker and crack in plastic mold, are mainly due to the stress generated in the vertical direction of tensile stress during plastic molding, and the difference between the yield of the non oriented part and the heavy flow orientation of the weight polymer molecules is shown.
The general solutions to such problems are as follows:
(1) Eliminate the interference of gas and other impurities, and fully dry the plastic.
(2) Reduce the material temperature, adjust the temperature of the material barrel in sections, and increase the mold temperature appropriately.
(3) Increase injection pressure and reduce injection speed.
(4) Increase or decrease the back pressure of pre molding and reduce the screw speed.
(5) Improve the exhaust condition of flow passage and cavity.
(6) Clean the nozzle, runner and gate for possible blockage.
(7) Shorten the molding cycle. Annealing can be used to eliminate crazing after demoulding: keep polystyrene at 78 ℃ for 15 minutes, or 50 ℃ for 1 hour, and heat polycarbonate to 160 ℃ for several minutes.
Most quality problems in the production process of plastic molds are caused by process conditions, materials, or maintenance of machines and molds. Therefore, in order to produce high-quality, high-precision and high-level plastic products, it is necessary to control the whole production process in an all-round way. In terms of details, the plastic mold, injection molding equipment, the technical experience of operators, the production environment of the workshop and raw materials all reach high standards.

Transparent plastic products are in high demand in various industries, such as automotive, packaging, and consumer goods. However, the production of transparent plastic parts can be challenging due to the occurrence of defects, such as hazing, cloudiness, or discoloration. These defects can significantly impact the quality of the product and reduce its value. Here are the causes and solutions for transparent defects in plastic molds:

Causes of Transparent Defects in Plastic Moulds

  1. Poor Material Quality: The quality of the plastic material used to produce transparent parts plays a significant role in the appearance and transparency of the final product. Poor quality materials can lead to defects such as bubbles, discoloration, or hazing.
  2. Inconsistent Cooling: During the cooling process, if the temperature is not uniform or if the cooling rate is not consistent, it can cause uneven crystallization, leading to transparency defects in the plastic part.
  3. Improper Mold Design: Improper mold design can also cause transparent defects in plastic parts. Poor venting or inadequate cooling can lead to trapped air or excessive heat, which can result in defects such as hazing or discoloration.

Solutions for Transparent Defects in Plastic Moulds

  1. Use High-Quality Materials: Using high-quality plastic materials can reduce the occurrence of defects in transparent plastic parts. The selection of materials with a low level of impurities and uniform molecular structure can result in higher clarity and transparency in the final product.
  2. Uniform Cooling: Uniform cooling is essential to minimize transparency defects. Ensuring that the cooling process is consistent and evenly distributed can reduce the occurrence of crystallization and prevent hazing or cloudiness in the final product.
  3. Proper Mold Design: Proper mold design is crucial to achieving high-quality transparent parts. The mold design should incorporate adequate venting and cooling systems to prevent the formation of trapped air or excessive heat, which can cause defects.
  4. Maintenance and Cleaning: Regular maintenance and cleaning of the molds can also reduce the occurrence of transparency defects. This includes cleaning the molds to remove any debris or impurities that may affect the quality of the final product.

In conclusion, the occurrence of transparency defects in plastic molds can significantly impact the quality of the final product. However, by identifying the causes and implementing solutions such as using high-quality materials, uniform cooling, proper mold design, and regular maintenance and cleaning, manufacturers can produce high-quality transparent plastic parts that meet the desired specifications.

en English